ブックタイトルWEB GUIDE CONTROL SYSTEMS

概要

WEB GUIDE CONTROL SYSTEMS

System components 5Liteguide Controller AE1000Power supply voltage 100 to 240 V AC, 50/60 Hz ±10%Power consumption 300 VA (Incoming current 50 A, 5 ms type (200 V))Power source fuse 250 V AC, 3.15 A (Time-lag type)Ambient temperature 0 to +50?CAmbient humidity 35-85% RH or below (no condensation)Vibration resistance 3.5 mm, 1 G, 3 to 150 Hz, 3 directions (1 hour)Power supply noise 2.5 kVp-p, Normal mode, Common mode 50 nS, 1 μS widthUsage atmosphere Area with no water, flammable or corrosive gases, and little dust.Mass Approx. 5 kgInput2 sensor systems: Voltage input maximum ±5 V (No input resistance/2 kΩ)Current input 0-20 mA (input resistance converted to 240 Ω)2 analog shift systems: Voltage input maximum ±10 VCentering: Proximity sensor input (0-8 V, 1.2 kΩ input resistance)(Applies to: MD0004270-JA)Position transmitter: Voltage input maximum ±10 VPhoto coupler input (12 V DC, 15 mA): Remote controller: Operation mode switching(auto/manual/centering)Operation keys (left/right/auto balance/reverse)System selection (EPC1/EPC2)Locks: 3 pointsActuator end limit: 2 pointsOutputElectrical actuator: K12 ±24 V DC, 1 A (maximum)K62 ±36 V DC, 2 A (maximum)K80 ±48 V DC, 2 A (maximum)Lamp power source: 4 to 12 V DC, variable (maximum 1 A)Fine tuner, Position transmitter: ±5 V power source (maximum 0.1 A)Sensors: ±15 V power source (+15 V, 1 A; -15 V, 0.2 A)(Note: The current capacity on the + side combined with the lamp power source isless than 1 A.)Centering proximity switch power source: 8 V DC (maximum 30 mA)2 indicator systems: Voltage output Maximum ±10 V (load resistance 2 kΩ or greater)Deviation outputPosition transmitter outputPhoto coupler output (24 V DC, 40 mA): Remote controller: Operation mode state (auto/manual/centering)System state (EPC1/EPC2)NOR/REVAlarms Excessive deviationEnd limitActuator lockActuator excessive load* Amplifier fault* "Amplifier fault" shares the same terminal as "NOR/REVoutput." You can switch from one to the other.IP grade IP20 (IP grade for the front panel only: IP30)? This model can be connected to the standard Nireco sensorsused by the previous AE900E and AE900L models. (Somesensors will need to be used together with a preamplifier.)? The AE1000 can be connected directly to the K12 and K62motor-driven actuators.In addition, it can be connected to an AC servo actuator via adriver.? Has 2 systems, a sensor input stage and a shift input stage,which can be switched for use.? The AE1000 has a large, white-backlit LCD display that iseasier to read and can allow the operator to check moreinformation than before.System componentsThe Liteguide Controller AE1000 carries out EPC (Edge Position Control) through a combination of Photoheads(PH16B) and Ultrasonic Sensor (UH01). It carries out CPC (Center Position Control) through a combination ofPhotoheads and Autowide Sensor (AWE280, etc.). It carries out LFC (Line Follower Control) through a combinationof the LH19 and LH110.